Date | Content Revision |
User opinion | Comment | Approved by moderator? |
---|---|---|---|---|
CORRECT | samsung z 500 data kable is tihis correct l tryed and worked not used pin 19 only use 2,3,9 vcc and other pin outs is same your thanks all pinouts see you later | APPROVED | ||
CORRECT | APPROVED | |||
CORRECT | APPROVED | |||
CORRECT | I made cable according to this description works OK. | APPROVED | ||
INCORRECT | D428, E620, E720, E810, P400, P408, P730, P735, S341i, S342i, S410i cell phones. | APPROVED | ||
INCORRECT | hi the pinout is correct however the pin numbering is reversed, the service manual uses numbering where rightmost pin is pin 1. | APPROVED | ||
CORRECT | In USB data cable, Pin 10 on the phone connector should go to PC USB Pin 3; Pin 15 on the phone connector should go to PC USB Pin 2. I tested on Z500! | APPROVED | ||
2008-12-03 23:16:05 | rev. 2 | CORRECT | This is like view from behind. So numbers of pins in the cable match numbers of pins in the device if you look at the device connection port, when it lays normaly (display/keys up). No need to mirror pins... that what confused me at first. Used this pinout to make cable for Samsung YP-T10 withot pins 3 and 4. Works fine. 6,13 - GND; 9 - +5V; 10 - D+; 15 - D-; | APPROVED |
2012-06-08 22:20:24 | rev. 3 | ERROR FIXED | APPROVED | |
2012-06-08 22:21:33 | rev. 3 | ERROR FIXED | 24-контактный разъём. 19 GND 16 USB +5V 15 USB D+ 10 USB D- 8 RxD 9 TxD | APPROVED |
2012-06-08 22:22:12 | rev. 3 | ERROR FIXED | Телефоны D428, E620, E720, E810, P400, P408, P730, P735, S341i, S342i, S410i, Z130, Z140, Z300, Z500, ZV10, ZV30 24-контактный разъём. 19 GND 16 USB +5V 15 USB D+ 10 USB D- 8 RxD 9 TxD Подробная распиновка: 1 - воздух (тоесть не куда не подключен) 2 - DCL_DETECT 3 - DEBUG_DSR 4 - воздух 6 - JIG_ON 7 - воздух 8 - SDS_RxD 9 - SDS_TxD 10 - USB_D_MINUS 11 - воздух 12 - GND 13 - DEBUG_RxD 14 - DEBUG_TxD 15 - USB_D_PLUS 16 - USB_5 17 - DEBUG_DCD 18 - DEBUG_RI 19 - GND 20 - DEBUG_RTS 21 - VBAT 22 - VBAT 23 - DEBUG_CTS 24 - DEBUG_DTR Если кабель прошивочный, тогда 3,4 должны быть соединены через диод 1N4148 к 16 (USB +5V). Если кабель для синхронизации, тогда должна быть перемычка 6 и 13. | APPROVED |
Date | Content Revision |
Author | Comment |
---|---|---|---|
2018-03-21 09:14:51 | rev. 4 | ppwo |
Pinouts.ru > Pinout of Samsung D428, E620, E720, E810, P400, P408, P730, P735, S341i, S342i, S410i, Z130, Z140, Z300, Z500, ZV10, ZV30 cell phones cable connector and layout of 24 pin Samsung cell phone special connector and 4 pin USB A or USB B plug connector |
should be correct |