Pinouts >  Распиновки слотов расширения на материнской плате  >  obsolete computers pinouts
96 pin DIN 41612 (3x32) female connector layout
Разъем 96 pin DIN 41612 (3x32) female
The ECB-bus was defined in 1984 by the german company KONTRON. It was defined of 100x160mm-europa-card and used 2x32 pins (row a and c). Later the third (middle) row of pins was defined for 16-bit-systems. Such bus uses all 3x32pins.

Row a & c (for 8 bit)

Pin Name Desciption
a1 + 5V + 5 volts dc
a2 D 5 D Data line bit 5
a3 D6 Data line bit 6
a4 D3 Data line bit 3
a5 D4 Data line bit 4
a6 A2 Address 2
a7 A4 Address 4
a8 A5 Address 5
a9 A6 Address 6
a10 WAIT/ CPU wait
a11 BUSRQ/ Bus request
a12    
a13    
a14    
a15    
a16    
a17    
a18 A14 Address 14
a19    
a20 M1/ first cycle
a21    
a22    
a23    
a24    
a25    
a26    
a27 IORQ/ in/out request
a28 RFSH/ refresh cycle
a29 A13 Address 13
a30 A9 Address 9
a31 BUSAK/ bus acknowledge
a32 GND signal ground
Pin Name Desciption
c1 +5V +5 volts dc
c2 D0 Data line bit 0
c3 D7 Data line bit 7
c4 D2 Data line bit 2
c5 A0 Address 0
c6 A3 Address 3
c7 A1 Address 1
c8 A8 Address 8
c9 A7 Address 7
c10    
c11 IEI interrupt enable in
c12    
c13    
c14 D1 Data line bit 1
c15    
c16 IEO interrupt enable out
c17 A11 Address 11
c18 A10 Address 10
c19    
c20 NMI/ not maskable interrupt
c21 INT/ normal interrupt
c22 WR/ write cycle
c23    
c24 RD/ read cycle
c25 HALT/ cpu stopped
c26    
c27 A12 Address 12
c28 A15 Address 15
c29    
c30 MREQ/ memory request
c31 RESET/ cpu reset
c32 GND signal ground

Row b (additional for 16 bit)

Pin Name Desciption
b1 +5V +5 volts dc
b2 A20 Address 20
b3 A21 Address 21
b4 A22 Address 22
b5 A23 Address 23
b6 D8 Data line bit 8
b7 D9 Data line bit 9
b8 D10 Data line bit 10
b9 D11 Data line bit 11
b10 D12 Data line bit 12
b11 D13 Data line bit 13
b12 D14 Data line bit 14
b13 D15 Data line bit 15
b14 IRQ7 interrupt 7
b15 IRQ6 interrupt 6
b16 IRQ5 interrupt 5
b17 IRQ4 interrupt 4
b18 IRQ3 interrupt 3
b19 IRQ2 interrupt 2
b20 IRQ1 interrupt 1
b21 IRQ0 interrupt 0
b22 IOWR I/O write
b23 ?? ??
b24 IORC I/O read
b25 MRDC Mem read
b26 ?? ??
b27 MWRC Mem write
b28 DS0 Data Select 0
b29 DS1 Data Select 1
b30 OFF bus driver tristate
b31 LOCK bus driver tristate disabled
b32 GND signal ground
DS0 DS1 Description
0 0 data transfer 16-bit
0 1 only bit 0-7
1 0 only bit 8-15
1 1 no data transfer

Note: / = Active Low

The DIN 41612 connector has different pin assignments assigned by various manufacturers, such as Kontron, J&K, ELZEY80, Conitec, etc.

 

На эту распиновку нет ни одного отзыва! Если вы знаете, правильная она или нет, - нажмите на соответствующую кнопку ниже.

Эта распиновка
Источник(и) этой и дополнительной информации: One issue of the magazine computer-technik (c"t) in 1984 and Gerd Wilken
Copyright © 2000-2024 by pinouts.ru team, except user uploaded images.
No portion of this webpage may be reproduced in any form without visible link to pinouts.ru .
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.
Change privacy settings